Home -> RV-7 and RV-7A topics from Nov 2003:

Sunday, November 2, 2003

The Right Primer
SoCAL RendezVous Warm-Up!
7A tail tie-down bracket

Monday, November 3, 2003

Fuse Block Mounting
Tank stiffeners

Tuesday, November 4, 2003

Oil cooler hose/fitting issues: RESOLVED
R-911 Rudder bottom
Roll 'em up
Gretz heated pitot static

Wednesday, November 5, 2003

Rear Spar .... dimple or Countersink?
Fuel Tank Pickup Anti Rotation Bracket
Capacitive Fuel Senders
Testing for leaks before closing the tank

Thursday, November 6, 2003

Painting the airframe
Manual or Electric Trim
Manual Trim ideas
Kit number poll
tip up vs. slider question
CNX80 price

Friday, November 7, 2003

SoCAL RV RendezVous is GO!!!
Need a bolt guys
7a Builders
Performance survey again
Relocating RV7 Kit to Las Vegas
Paint information Thanks

Saturday, November 8, 2003

status
Fitting the Cowl
electric trim wire
Flying story / thread

Sunday, November 9, 2003

Empenage Fairing Attach
Builder Poll
paint booth exhaust fan
Dimpling and Riveting pressures?
Wash Primer Blues

Monday, November 10, 2003

Taildragger or tricycle
wheel pantaloons
Wing skins & Leading edge.
Flying story / thread (long)
Performance numbers, If you want them just ask
Battery Tray for RV7 / 9 A
Aluminum Air Vents

Tuesday, November 11, 2003

Pre-order info
Mag type?
Mag plus an electronic ignition
RV7A Kit for sale

Wednesday, November 12, 2003

How much do the prices go up?
Ending a project (was Project for Sale ) - long
UPS to Garmin to Discontinued :-(

Thursday, November 13, 2003

Resale Values
Motivation
Checkoway's Site
7A step installation
UPS rumor
Electric elevator trim option
[Fwd: RV-List: UPS to Garmin to Discontinued :-(]

Friday, November 14, 2003

Flap Tape
Finish Kit Timing
SoCAL RV RendezVous Report

Sunday, November 16, 2003

Riveting HS-411PP - wrong rivet size?
Riveting short aileron control tubes

Monday, November 17, 2003

Countersunk Screws in Fiberglass....
Rivets and rivet guns, etc
DUCKWORKS-???
Checkoway's Sit

Tuesday, November 18, 2003

Bending fuel line up to Facet pump
Insurance ?
N number?
Update on parachute system.
To FADEC or not
Van's Windscreen Com Ant
Pipe tools?
Closing the Wings
4" reach yoke
Tailwheel Spring Mount

Wednesday, November 19, 2003

W & Balance A1B6 engines
HI0 260 D1A
Gyros Choice

Thursday, November 20, 2003

Canopy Finished
AeroElectric Connection Seminar
New kid on the block
Canopy Fitting Question
Elevator Travel limits
rivet set for tank work
bolt holes lower spar
Centurion 1.7 diesel
F-790 Pushrod to elevator horns attach bolt

Friday, November 21, 2003

H-Stab Attach
XP360
Internet Archive Website
Big Mistake, or not?
epanelbuilder.com problems

Saturday, November 22, 2003

Empenage Kit - Electric Elevator Trim Option
Elevator Travel limits-no adding
Powerplant Options
Fuel Inj. ret.line
Blue Mountain EFIS-One for sale
digital levels
Electric vs. Manual trim
tools :)
Low Oil Temps

Sunday, November 23, 2003

Wing size - Basement Stairs
tool reviews?
Digest Number 1029 Tool Reviews
panel builder problems
Wing Conduit Material and Location

Monday, November 24, 2003

Fellow RV builders- DRDT-1 dimpling tool
Fiberglass tail tips
rolling front deck skin edges
Another Tools Question
builders logs
Aileron Stops
Diesel update ... (Deltahawk) Fwd: timeline for availability?
ky76a wiring diagram - URGENT

Tuesday, November 25, 2003

bell crank?
Center Consul
builders logs-Now help in building
Reamers
Firewall Forward Kits
C-660 Side Skirt
5 point military style seat belts

Wednesday, November 26, 2003

Reaming Bushings
Need advice on U-1201/2 dilution for spraying
Digest Number 1034
Tools & Compressor
Fibergalss wing tip reinforcement
Priming in the Cold
primed plate nuts
Up close look at RV-7A

Thursday, November 27, 2003

up close and personal...
nulite rings, Monroy ATD, and life vests -- for sale.
Digest Number 1035 Primed nut plates
Happy Thanksgiving!

Friday, November 28, 2003

fabric adhesive
Hatch release handle...
Tools and Compressors
drilling HS attach holes

Sunday, November 30, 2003

Bending the longeron
Digest Number 1037
Dynon install for sliders
Needs some help in the decision
Torque outputs for CS Propellers
How do you deal with an "out dent"
Priming in the Cold - Parts Cleaning
Close look at RV-7 or 7A


Search Messages:

Group:

any word all words exact

About

Search Tips